BEC MX-210NPV Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 114

BEC MX-210NPV Скачать руководство пользователя страница 14

Product Overview

System Recovery Procedure & Cabling

9

BEC MX-210NPV User Manual

System Recovery Procedures

The purpose is to allow users to restore the MX-210NPV to its initial stage when the device is outage,
upgraded to a wrong / broken firmware, cannot access to the GUI with wrong username and/or
password, etc.

Step 1 – Configure your PC Network IP Address

Before performing the system recovery, assign this IP address and Netmask to your PC,

192.168.1.100

and

255.255.255.0

respectively.

Step 2 – Reset your MX-210NPV Device

2.1

Power off your MX-210NPV

2.2

Power on the MX-210NPV while pushing the RESET button with a small pointed object (such as
paper clip, needle, toothpick, etc.).

2.3

When the POWER LED turns RED, keep holding and pushing the RESET button until the
INTERNET LED flashes in GREEN

Step 3 – Restore your MX-210NPV Device

With INTERNET light flashes green, MX-210NPV is in recovery mode and ready for a new Firmware.

3.1 Open a web browser and type the IP address,

192.168.1.1

, to access to the recovery page.

NOTE

: In the recovery mode, MX-210NPV will not respond to any PING or other requests.

3.2 Browse to the new Firmware image file then click Upload to start the upgrade process.

3.3 INTERNET LED turns red means the Firmware upgrade is in process.

DO NOT power off or reboot the device, it would permanently damage your MX-210NPV.

3.4 INTERNET LED turns green after the Firmware upgrade completed

3.5 Power cycle on & off to regain access to the MX-210NPV.

Cabling

One of the most common causes of problems is bad cabling. Make sure that all connected devices
are turned on. On the front panel of the product is a bank of LEDs. Verify that the LAN Link and LEDs
are lit. If they are not, verify that you are using the proper cables.

«
...
12
13
14
15
16
...
»

Содержание MX-210NPV



















































































































Отзывы:

Нет отзывов