BEC MX-210NPV Скачать руководство пользователя страница 12

Страница: 12 / 114

Product Overview

Device Description (Front Panel LEDs)

BEC MX-210NPV User Manual

Device Description

Front Panel LEDs

LED

STATUS

DESCRIPTION

Power

Green

System is up and ready

Red

Boot failure

Ethernet Port

LAN 1 ~ 2

Green

Transmission speed is at Gigabit speed (1000Mbps)

Orange

Transmission speed is at 10/100Mbps

Blinking

Data being transmitted/received

Wireless

Green

Wireless connection established

Green blinking

Data being transmitted / received

Orange

WPS configuration is in progress

LTE

(Received Signal

Strength
Indicator)

Green

RSSI greater than -69 dBm. Excellent signal condition

Green

Flashing quickly

RSSI from -81 to -69 dBm. Good signal condition

Orange

Flashing quickly

RSSI from -99 to -81 dBm. Fair signal condition.

Orange

Flashing slowly

RSSI less than -99 dBm. Poor signal condition.

Orange

No signal and the cellular module is in service

Off

No LTE module or LTE module fails

Green & Orange MX-210NPV is either in debug mode or in upgrading firmwere process

Internet

Green

IP address has received, and traffic is passing thru the device.

Red

IP address request has failed.

Off

MX-210NPV is either in bridged mode or WAN connection not ready.

Содержание MX-210NPV



















































































































Результаты поиска

Содержание MX-210NPV

Отзывы:

BEC MX-210NPV, Руководство пользователя, Страница: 12 / 114

Результаты поиска

Содержание MX-210NPV

Отзывы: