BayTech MMP страница 27 Скачать руководство пользователя | Manualshive

Страница: 27 / 68

background image

Page

27

--------------------------------------------
| User | Assigned Outlets |
| | C1,1| C1,2| C1,3| C1,4|
--------------------------------------------
1) Engineer | N

|

Y

| N | N |

--------------------------------------------
A)...Add User

D)...Delete User

R)...Rename User

C)...Change Circuit Group
Enter user number to assign Outlets, A, D, C or R.

Assigned

Outlets

Enter Outlet number(s):

Select 1),

assigns outlets to a user. The unit will prompt for outlet number:

Type the number of the outlet to be assign. For
example, if you want engineer to have access to
Outlet (C1,2), enter the number 2, followed by
<cr>. If you want engineer to have access to
Outlets (C1,2), (C1,3), and (C1,4) enter the
numbers 2, 3, and 4 separated by commas
followed by <cr>.
The unit redisplays the Assigned Outlet Menu of
the user with a

“Y”

for the assigned outlets.

--------------------------------------------
| User | Assigned Outlets |
| | C1,1| C1,2| C1,3| C1,4|
--------------------------------------------
1) Engineer | N

|

Y

| N | N |

--------------------------------------------
1)...Add Outlet(s)

2)...Remove Outlet(s)

3)...Add All Outlets

4)...Remove All Outlets

C)...Change Circuit Group

Select 2),

removes individual outlet from a user. The unit will prompt for

outlet number

Enter Outlet number(s):

Type the number of the outlet to be removed from
the user’s access. For example, if you want to
remove Outlet (C1,2), enter the number 2,
followed by <cr>. If you want engineer to have
access to Outlets (C1,2), (C1,3), and (C1,4) enter
the numbers 2, 3, and 4 separated by commas
followed by <cr>.The unit redisplays the
Assigned Outlet Menu of the user with an

“N”

for

the outlets NOT assigned.

--------------------------------------------
| User | Assigned Outlets |
| | C1,1| C1,2| C1,3| C1,4|
--------------------------------------------
1) Engineer | N

|

Y

| N | N |

--------------------------------------------
1)...Add Outlet(s)

2)...Remove Outlet(s)

3)...Add All Outlets

4)...Remove All Outlets

--------------------------------------------
| User | Assigned Outlets |
| | C1,1| C1,2| C1,3| C1,4|
--------------------------------------------
1) Engineer | N

|

Y

| N | N |

--------------------------------------------
1)...Add Outlet(s)

2)...Remove Outlet(s)

3)...Add All Outlets

4)...Remove All Outlets

C)...Change Circuit Group

The Assigned Outlet Menu displays the outlets
a user can access.
Select a

user number

from the Managed User

Menu, the unit will display the Assign Outlet
Menu:

NOTE:

If an outlet user’s list is changed while

the user is logged in, their outlet list changes
dynamically. If enabled, an updated outlet
status report will be issued.

“Y”

means the

outlet is assigned to the user.

“N”

means the

outlet is NOT assigned to the user.

«
...
25
26
27
28
29
...
»

Содержание MMP





































































Отзывы:

Нет отзывов

Похожие инструкции для MMP

EasySmart DGS-1100-08

Бренд: D-Link Страницы: 44

Бренд: pathway Страницы: 28

Бренд: GE Страницы: 302

Бренд: Accedian Страницы: 2

Бренд: Panio Страницы: 5

Бренд: ATEN Страницы: 17

Бренд: Micrel Страницы: 15

Бренд: Jerguson Страницы: 4

SmartSTACK ETHERNET ELS10-27

Бренд: Cabletron Systems Страницы: 126

Instant On 1930 Series

Бренд: Aruba Страницы: 8

EXT-HDMI-CAT5-844

Бренд: Gefen Страницы: 28

CT.TS005.501401

Бренд: Talkswitch Страницы: 9

Бренд: Penguin Computing Страницы: 71

Бренд: PCB Piezotronics Страницы: 31

Бренд: AMBIENTECH Страницы: 4

24/48 10/100 Ports + 2GE

Бренд: Accton Technology Страницы: 512

TIMEGUARD IS3N-20

Бренд: Theben Страницы: 2

Intraplex T1 DCS-9530 CrossConnect System

Бренд: GatesAir Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды