BayTech MMP страница 5 Скачать руководство пользователя | Manualshive

Страница: 5 / 68

background image

Page

5

ABOUT THIS MMP OWNER’S MANUAL

COMPLIANCE

STANDARD

This document provides information required for installing and operating your Bay Tech equipment. It
should allow the user to connect to, power up, and access an applications menu where peripheral
equipment can be controlled. We recommend reading this manual carefully, while placing special
emphasis on correct cabling and configuration. If you have any problems with your installation, please
contact a BayTech Applications Engineer at

228-563-7334

, or toll free from anywhere in the United

States using

1-800-523-2702

or contact us at our Web Site,

www.baytech.net

.

BayTech manufactures many remote site management power products and data switches. If you would
like information on any of these products, please contact BayTech Customer Service at the above
numbers or visit our web site.

Conventions used in this manual include:

CAUTION:

This term is used to denote any condition that could possibly result in physical

harm to personnel or damage to equipment.

IMPORTANT:

This term is used to denote conditions that could result in the loss of

communications or to highlight the proper functioning of equipment.

NOTE:

This term is used to denote items of interest to the user.

<cr>:

Carriage Return or ENTER

The information in this document is subject to change without notice. The statements, configurations,
technical data, and recommendations in this document are believed to be accurate and reliable, but are
presented without express or implied warranty. Users must take full responsibility for their applications
of any products specified in this document. The information in this document is proprietary to Bay
Technical Associates, Inc.

In the interest of improving internal design, operational function, and/or reliability, Bay Technical
Associates, Inc reserves the right to make changes to the products described in this document without
notice.

Bay Technical Associates, Inc does not assume any liability that may occur due to the use or application
of the product(s) or circuit layout(s) described herein.

BayTech units are in accordance with the general requirements of

Standard for Information Technology

Equipment

(ETL listed, conforms to ANSI/UL 60950-1 2

nd

Edition and CAN/CSA C22.2 No. 60950-00.

CE conforms to IEC 60950.)

Equipment installations are to be in accordance with the Canadian

Electrical Code, Part I, CSA C22.1-02; General Requirements – Canadian Electrical, Part II, CSA
C22.2 No 0-M91; the National Electrical Code, NFPA 70-2005; and the National Electrical Safety
Code, NFPA, IEEE C2-2002.

«
...
3
4
5
6
7
...
»

Содержание MMP





































































Отзывы:

Нет отзывов

Похожие инструкции для MMP

Бренд: Hama Страницы: 9

Бренд: OFFICINE OROBICHE Страницы: 7

Switch 4500 Family

Бренд: 3Com Страницы: 742

Бренд: 3Com Страницы: 940

Бренд: 3Com Страницы: 43

OfficeConnect WX1200

Бренд: 3Com Страницы: 646

Бренд: SMART-AVI Страницы: 2

Бренд: FS Страницы: 33

Бренд: ATEN Страницы: 17

Бренд: Abseco Страницы: 10

Бренд: Videosec Страницы: 5

Бренд: Linkskey Страницы: 2

Бренд: Ortech Страницы: 3

ConferenceHub TA-6500

Бренд: TeleAdapt Страницы: 16

Бренд: Longshine Страницы: 26

Бренд: Tripp Lite Страницы: 20

Бренд: H3C Страницы: 34

Бренд: S&C Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды