BayTech MMP страница 66 Скачать руководство пользователя

Страница: 66 / 68

Page

APPENDIX:

TACACS

CONNECTION

SCENERIOS

Different username and password in and power strip:

username Login



Case 1:

enabled, contact good, “Enable URPC usernames as backup” = disabled,

TACACS username Log in

OK.



Case 2:

enabled, TACACS contact good, “Enable URPC usernames as backup” = enabled,

TACACS username Log in

OK.



Case 3:

disabled or contact lost, “Enable URPC usernames as backup” = disabled,

TACACS username Log in

FAIL

. not validate the user.



Case 4:

disabled or contact loss, “Enable URPC usernames as backup” = enabled,

TACACS username Log in

FAIL.

not validate the user.

Same username and password in and URPC



Case 1:

enabled, TACACS contact good, “Enable URPC usernames as backup” = enabled,

user Log in

OK.



Case 2:

enabled, TACACS contact good, “Enable URPC usernames as backup” = disabled,

user Log in

OK.



Case 3:

disabled, or contact loss, “Enable URPC usernames as backup” = enabled,

user Log in

OK.

URPC validates the user.



Case 4:

disabled, or contact loss, “Enable URPC usernames as backup” = disabled,

user Log in

FAIL.

Neither nor the URPC can validate the user.

Parameters to determine if user should be able to log in:



TACACS enabled/disabled



Good/Bad TACACS connection



“Enable URPC usernames as backup” enabled/disabled



Username/password on TACACS and power strip are same/different

Different username and password in and power strip:

Power Strip username Login



Case 1:

enabled, contact good, “Enable URPC usernames as backup” = enabled,

Power Strip username Log in

OK.

Power strip validates the user.



Case 2:

disabled or contact loss, “Enable URPC usernames as backup” = enabled,

Power Strip username Log in

OK.

Power strip validates the user.



Case 3:

enabled, contact good, “Enable URPC usernames as backup” = disabled,

Power Strip username Log in

FAIL.

Power strip not validate the user.



Case 4:

disabled or contact loss, “Enable URPC usernames as backup” = disabled,

Power Strip username Log in

FAIL.

Power strip not validate the user.

Содержание MMP




































































Результаты поиска

Содержание MMP

Отзывы:

Похожие инструкции для MMP

Бренды по названию

Популярные бренды

BayTech MMP, Руководство пользователя

Результаты поиска

Содержание MMP

Отзывы:

Похожие инструкции для MMP

Бренды по названию

Популярные бренды