40
Commissioning step by step
User Manual PoolManager
®
74
Variation B: PoolManager
®
Chlorine/Bromine
Step 4: Calibration
Calibration (comparison) of
measured value for pH and
redox
1-point calibration pH. Please proceed as
described in the section
Calibration pH.
1-point calibration mV (optional). Please
proceed as described in the section
Calibration redox (mV).
Step 5: Control parameters pH
Configuration of the most
important parameters for
pH control
When refilling the pool, it may be sensible to
expand the top and bottom pH value alarms
and to adjust the p-range, as the pH value
can fluctuate somewhat during the starting
phase.
CAUTION: If the parameters are changed,
make absolutely sure that the values are set
back as soon as the pool water has stablised.
You can also use the configuration assistant.
Step 6: pH Value configuration
Possibility for automatically /
manually setting the pH value
in the pool water
Display shows the configured pH setpoint and
the current pH value in the pool water.
NOTE The pool water's pH value first has to
be set to pH 7.2 in order to facilitate
configuration of the redox value without issue.
Set pH operation mode to auto if
PoolManager
®
should make the configuration
fully automated. This process will take some
time, depending on pool size and water
quality.
Set operating mode to manual if you would
like to configure the pH value via manual
addition of pH-elevator and -reducer.
Step 7: Manual dosing mV (Cl / Br)
Configure the desired
chlorine or bromine level and
calculate the associated
redox (mV) value
The matching setpoint will depend on the
pool. It has to be calculated for the water in
the respective pool. Proceed as follows:
Set the pH value to pH 7.2
(see previous step)
Set the desired chlorine level in the pool via
manual dosing (or via manual addition of
chlorine) (in Germany, the recommended
value of 0.5 - 0.6 mg/l can also be set higher).
The volume of ChloriLiquid dosed is
determined by PoolManager
®
via the pool
volume entered. This volume can be
overwritten manually.
Check the desired chlorine level via manual
measurement (DPD). The redox value in
[mV], which PoolManager
®
shows for the
desired chlorine volume, is also the value that
has to be entered as the setpoint in the next
step.
Step 8: Control parameters mV (redox)
Configuration of the most
important parameters for
redox control
Set the mV value as the setpoint you read in
the previous step for the desired chlorine
level. Adjust the bottom and top alarm
accordingly. Check the proportional range.
You can also use the configuration assistant.
Action
Entry
Variation C: PoolManager
®
PRO
Step 4: Calibration
Calibration (comparison) of
measured values for pH, Cl,
and redox (only
1-point calibration pH. Please proceed as
described in the section
Calibration pH.
1-point calibration Cl/Br. Please proceed as
described in the section
Calibration chlorine /
bromine.
1-point calibration mV (optional). Please
proceed as described in the section
Calibration redox (mV).
Step 5: Control parameters pH
Configuration of the most
important parameters for pH
control
When refilling the pool, it may be sensible to
expand the top and bottom pH value alarms
and to adjust the p-range, as the pH value
can fluctuate somewhat during the starting
phase.
CAUTION: If the parameters are changed,
make absolutely sure that the values are set
back as soon as the pool water has stablised.
You can also use the configuration assistant.
Step 6: pH Value configuration
Possibility for automatically /
manually setting the pH value
in the pool water
Display shows the configured pH setpoint and
the current pH value in the pool water.
NOTE The pool water's pH value first has to
be set to pH 7.2 in order to facilitate
configuration of the redox value without issue.
Set pH operation mode to auto if
PoolManager
®
should make the configuration
fully automated. This process will take some
time, depending on pool size and water
quality.
Set operating mode to manual if you would
like to configure the pH value via manual
addition of pH-elevator and -reducer.
Step 7: Manual dosing Cl
Configuration of the
Enter the desired chlorine value (setpoint) as
follows:
Set the pH value to pH 7.2
(see previous step)
Set the desired chlorine level in the pool via
manual dosing (or via manual addition of
chlorine) (in Germany, the recommended
value of 0.5 - 0.6 mg/l can also be set higher).
The volume of ChloriLiquid dosed is
determined by PoolManager
®
via the pool
volume entered. This volume can be
overwritten manually.
Check the desired chlorine level via manual
measurement (DPD).
Step 8: Control parameters Cl
Configuration of the most
important parameters for
chlorine control
Set the desired chlorine level of 0.5 - 0.6 mg/l
as the setpoint. Adjust the bottom and top
alarm accordingly. Check the p-range.
You can also use the configuration assistant.
In the individual menu pages, it is possible to scroll forward and
backward at any time.
For further information, please refer to the corresponding chapters in
this user's manual or to the help function on the device.