Baroness LM315GC Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 86

Baroness LM315GC Скачать руководство пользователя страница 85

(7)

The equipment owner will not be charged for diagnostic labor that is directly
associated with diagnosis of a defective, emission-related warranted part, provided
that such diagnostic work is performed at a KYOEISHA U.S.A. INC or authorized
service dealer.

(11)

The repair or replacement of any warranted part otherwise eligible for warranty
coverage may be excluded from such warranty coverage if KYOEISHA CO.,LTD
demonstrates that the equipment has been abused, neglected, or improperly
maintained, and that such abuse, neglect, or improper maintenance was the direct
cause of the need for repair or replacement of the part.

(8)

KYOEISHA CO.,LTD is liable for damages to other engine or equipment components
proximately caused by a failure under warranty of any warranted part.

(9)

Throughout the equipment warranty period stated above, KYOEISHA CO.,LTD will
maintain a supply of warranted parts sufficient to meet the expected demand for such
parts and will obtain additional parts if that supply is exhausted.

(10)

Add-on or modified parts that are not exempted by the Air Resources Board may not
be used. The use of any non-exempted add-on or modified parts by the ultimate
purchaser will be grounds for disallowing a warranty claims. KYOEISHA CO.,LTD
will not be liable to warrant failures of warranted parts caused by the use of a non-
exempted add-on or modified part.

(5)

Any warranted part that is scheduled for replacement as required maintenance in
owner’s operating manual supplied is warranted for the period of time before the first
scheduled replacement date for that part.

(6)

If the part fails during the period of warranty coverage, repair or replacement of any
warranted part under the warranty provisions herein must be performed at
KYOEISHA CO.,LTD at no charge to the owner. Any such part repaired or replaced
under warranty will be warranted for the remainder of the period.

EV2018AA01-3

«
...
83
84
85
86
»

Содержание LM315GC























































































Отзывы:

Нет отзывов