Baroness LM315GC Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 86

Baroness LM315GC Скачать руководство пользователя страница 53

When it is switched to the down position, the
green LED on the steering column lights up.
The Up/Down speed of the mower unit is
affected by the engine rotation speed. When
the engine rotation is at low speed, the Up/
Down speed is at low as well.

Mower Unit Up Switch

Up Switch (with reel excess discharge system)

(#30727 - )

Warning

The reel cutter rotates while holding down the
up switch when the reel rotation switch is set
to the "MOW" (reel rotation) position.
Set the reel rotation switch to the "TRAVEL"
(reel stop) position except during mowing or
backlapping and using reel excess discharge
system.

Caution

Before using reel excess discharge system,
make sure that there are no people around
the machine.

Caution

The reel cutter rotates when using reel excess
discharge system.
Keep hands and feet away from moving parts.

Important

Do not press the up switch when the mower
unit is at lowered position.
Otherwise, the harness may get damaged.

Important

The reel cutter keeps rotating even if the
mower unit raised to the highest position while
holding down the up-switch.

Up Switch
The up switch is located in the operation
panel.
If the height of the mower unit is not
sufficient for traveling etc, set the reel
rotation switch to the "TRAVEL" (reel stop)
position and keep pressing the up switch to
operate the magnetic valve to raise the
mower unit to the highest position.

･

Reel excess discharge system
Reel refreshing is the function to remove
clippings inside the reel cutter by rotating
the reel cutter with the up switch on the
condition that the mower unit raised and the
reel rotation switch set to the "MOW" (reel
rotation) position.
With this function, falling of lumps of
clippings can be prevented during mowing
operation and the time of washing the
vehicle can be shortened.

(#30727 - )

3

WD

2

WD

MOW

TRAVEL

1

1dndt8-005

Up Switch (with reel excess discharge system)_001

1

Up Switch(with reel excess discharge
system)

Up Switch

( - #30726)

Caution

Up switch should be used only when the
height of the mower unit is not sufficient.
Do not press the up switch when the mower
unit is at lowered position.
Otherwise, the harness may get damaged.

The up switch is located in the operation
panel.
If the height of the mower unit is not sufficient
for traveling etc, keep pressing the up switch
to operate the magnetic valve to raise the
mower unit to the highest position.

･

Handling Instructions

LM315GC

Handling Instructions

Page 4-29

Operation of Each Section

«
...
51
52
53
54
55
...
»

Содержание LM315GC























































































Отзывы:

Нет отзывов