manualshive.com logo in svg

Baroness LM315GC, Руководство по эксплуатации для владельца, Страница: 84 / 86

Поделиться
Скачать
Baroness LM315GC Скачать руководство пользователя страница 84

GENERAL EMISSIONS WARRANTY COVERAGE:

・

Designed, built and equipped so as to conform with all applicable regulations; 
and

・

The following are specific provisions relative to your emission warranty coverage:

･

   Fuel Tank

･

   Fuel Cap

･

   Fuel Lines (for liquid fuel and fuel vapors)

･

   Fuel Line Fittings

･

   Clamps

･

   Vapor Hoses

･

   Carbon Canister

･

   Canister Mounting Brackets

･

   Connectors

(4)

Any warranted part that is scheduled only for regular inspection in owner’s operating
manual supplied is warranted for the warranty period stated above.

(1)

Coverage under this warranty extends only to the parts listed below (the evaporative
emissions control systems parts) to the extent these parts were present on the
equipment purchased.

(2)

The warranty period begins on the date the equipment is delivered to an ultimate
purchaser.  The warranty period is two years.

(3)

Any warranted part that is not scheduled for replacement as required maintenance in
owner’s operating manual supplied is warranted for the warranty period stated above.

You are responsible for presenting your equipment to a KYOEISHA U.S.A. INC or
authorized service dealer as soon as the problem exists.  The warranty repairs shall be
completed in a reasonable amount of time, not to exceed 30 days.  If you have a question
regarding your warranty coverage, you should contact 

ａ

 KYOEISHA U.S.A. INC at 510-215-

2111.

KYOEISHA CO.,LTD warrants to the ultimate purchaser and each subsequent purchaser
that the equipment is:

Free from defects in materials and workmanship that cause the failure of a warranted
part to be identical in all material respects to that part as described in KYOEISHA
CO.,

LTD’s application for certification.

EV2018AA01-2

Содержание LM315GC























































































Отзывы:

Нет отзывов