Baroness LM315GC Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 86

Baroness LM315GC Скачать руководство пользователя страница 75

1

Reel cutter (Cutting cylinder)

2

Bed knife (Bottom blade)

3

Lock nut

4

Cam bush

A

Max 0.3 mm (0.012 inch)

B

Bed knife (bottom blade) moving up

C

Bed knife (bottom blade) moving down

D

Center of cutter pin

E

Center of cam bush

Attaching Reel Cutter (Cutting Cylinder)

Caution

Both the reel cutter (cutting cylinder) and the
bed knife (bottom blade) are edged tools.
Handle them carefully, since they could cut
your hands and feet.

Follow the instruction below to replace the reel
cutter bearing (right/left) and seal.
Use 30204JRP6 as bearing.

Fill up (Excelite EP No.2) to the bearings and
seal.
Attach the reel cutter (cutting cylinder) to the
frame like the figure below.
Tighten the inner nut and check the bearing
for backlash.
Loosen the inner nut at the level that the reel
cutter (cutting cylinder) can be rotated lightly
by your hand and you don't feel the
backlash.
Tightening torque: 7 N-m (71.4 kgf-cm /
61.96 lb-in)
Tighten the outer locknut.

4

3

5

1

1

8

2

7

6

wggg9e_001

Attaching Reel Cutter (Cutting Cylinder)_001

1.

2.

3.

4.

5.

1

Bearing

2

Seal

3

Reel cutter (Cutting cylinder)

4

Inner nut

5

Outer nut

6

Key

7

Cover

8

Pin

Maintenance (Main Body)

Removing/Installing Tires

Front Tire

Follow the steps below to remove the front
tire:

Loosen the bolts.

1

lm2ieh-004

Front Tires_001

1

Heat-treated bolt

Securely place the jack beneath the jack-up
point of the front right/left frame area, and
then raise it until the tire lifts off the ground.
"Jack-up Points" (Page 5-7)
Remove the bolts.
Remove the tire from the wheel mounting
base.

1.

2.

3.
4.

Maintenance

LM315GC

Maintenance

Page 5-13

Maintenance (Main Body)

«
...
73
74
75
76
77
...
»

Содержание LM315GC























































































Отзывы:

Нет отзывов