Baroness LM315GC Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 86

Baroness LM315GC Скачать руководство пользователя страница 80

Grease Change of Transmission

The transmission is located behind the driver's
seat.
Change grease every two years.

Grease type

Pyronoc CC1

Grease quantity

400 g

1

ib4tfi-001

Grease Change of Transmission_001

1

Transmission

Change of Fuse

Fuses

Warning

When performing maintenance on the
electrical system, be sure to remove the
negative battery wire.

Caution

If a fuse blows, a short may have occurred
within the electrical circuit.
Check for the cause, such as faulty terminal
connections, damaged wiring or terminals, or
incorrect wiring.

The fuses are located under the underseat
cover and consist of the light harness fuse
and the main harness fuse for the entire
circuit.
Both are glass fuses 20 A (φ6.4 x 30 mm).

1

2

7syu5e-002

Fuses_001

1

Main harness fuse

2

Light harness fuse

Check the Operation Status of the Relay

Mower Unit Control Relay

The relay box is located behind the seat.
This controls Up/Down of the mower unit and
Rotate/Stop of the reel cutter (cutting
cylinder).
The operating condition can be checked by
the illumination of the LEDs.

3

2

1

x1d47c-001

Mower Unit Control Relay_001

Refer to the table below to check the LED
status.

　

　

Condition LED status

1

Front right up/down
cylinder
(Reel rotation)

Down

ON

Up

OFF

2

Center mower up/
down cylinder
(Before pressing
Raise/Lower switch)

Up

ON

Down

OFF

3

Center mower up/
down cylinder
(After pressing
Raise/Lower switch)

Down

ON

Up

OFF

LM315GC

Maintenance

Page 5-18

Maintenance (Main Body)

«
...
78
79
80
81
82
...
»

Содержание LM315GC























































































Отзывы:

Нет отзывов