Baroness LM315GC Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 86

Baroness LM315GC Скачать руководство пользователя страница 38

Adjustment Before Operating

Adjustment of Seat

Use the seat adjustment levers to adjust the
seat.
Adjust the position according to the operator's
body size.

Use the forward/backward adjustment lever
to adjust the seat back and forth.
Use the backrest tilt adjustment lever to
adjust the angle of the backrest.
Pull out the suspension adjustment handle
and move it up or down to adjust the
firmness of the seat suspension.
Observe the suspension adjustment scale
while making adjustments. (50 - 160 kg)
The seat can be adjusted up and down in 3
levels by pulling up the forward tilt angle
adjustment lever.

5

4

3

1

2

s1gskp-017

Adjustment of Seat_001

1

Forward/backward adjustment lever

2

Angle adjustment lever

3

Suspension adjustment handle

4

Suspension adjustment scale

5

Forward tilt angle adjustment lever

1.

2.

3.

4.

Adjustment of Steering Wheel

Warning

Since it is dangerous, do not adjust the
steering wheel while traveling.

Caution

Be sure the steering wheel position is securely
locked.
It would be extremely dangerous if it becomes
loose while traveling.

Caution

When operating the height adjustment lever,
be careful not to pinch your hands.

The steering wheel arm can be adjusted up or
down.
Adjust the position according to the operator's
body size.
Pull up the height adjustment lever, position
the steering wheel arm to a proper position for
your work and push down the height
adjustment lever to lock it.
The height adjustment lever is attached to the
right of the seat.

1

2

75uxaw-006

Adjustment of Steering Wheel_001

1

Steering wheel arm

2

Height adjustment lever

LM315GC

Handling Instructions

Page 4-14

Adjustment Before Operating

«
...
36
37
38
39
40
...
»

Содержание LM315GC























































































Отзывы:

Нет отзывов