manualshive.com logo in svg

Baroness LM315GC, Руководство по эксплуатации для владельца, Страница: 69 / 86

Поделиться
Скачать
Baroness LM315GC Скачать руководство пользователя страница 69

Jacking up the machine

About the Jacking up the machine

Warning

When replacing a tire or beginning any other
maintenance or repairs, be sure to chock the
wheels to prevent the machine from moving.
Before jacking up the machine, park it on a
hard, flat surface such as a concrete floor and
remove any obstacles that could prevent you
from performing the work safely.
When necessary, use an appropriate chain
block, hoist, or jack.
Support the machine securely with jack stands
or appropriate blocks.
Failure to do so may cause the machine to
move or fall, resulting in injury or death.

Use the jack-up points identified in this manual
when jacking up the machine.
Only place a jack under the jack-up points
specified.
Placing a jack at any other point could result in
damage to the frame or other parts.

Jack-up Points

1

2

3

rwyt62-085

Jack-up Points_001

1

Front right frame

2

Front left frame

3

Engine mount frame

Front right frame

rwyt62-053

Jack-up Points_002

Front left frame

rwyt62-054

Jack-up Points_003

Engine mount frame

rwyt62-055

Jack-up Points_004

1.

2.

3.

Maintenance

LM315GC

Maintenance

Page 5-7

Jacking up the machine

Содержание LM315GC























































































Отзывы:

Нет отзывов