Bard Q-TEC Q24H2D Series Скачать руководство пользователя

Страница: 30 / 44

Manual 2100-603

Page

30 of 44

VENT OPTIONS

BAROMETRIC FRESH AIR DAMPER

(Standard)

Before starting, make sure the power has been turned

off. The return air grille panel must be removed. The

fresh air damper assembly can be seen on the back of

the unit. See Figure 22.
1. The fresh air damper is attached to the back of

the unit with one screw on either side of the

assembly. Both of the screws must be removed.

2. Once the mounting screws are removed, tilt the

assembly down and lift it out.

The mist eliminator can be seen through the opening.

The mist eliminator must be raised up and the bottom

can be pulled toward the front of the unit.

COMMERCIAL ROOM VENTILATOR (Option)

Before starting, make sure the power has been turned

off. The return air grille panel must be removed.

The commercial room ventilator (CRV) can be seen

after the panel has been removed. The CRV must be

removed to gain access to the mist eliminator.
1. The two mounting screws in the front of the CRV

must be removed.

2. The power connectors for the CRV (located on

the right side of the unit) must be disconnected.

Squeeze the tabs on the sides of the connector

and pull straight out. Unplug both of the

connectors.

3. Slide the CRV straight out of the unit.
The mist eliminator can be seen through the opening in

the back of the unit. The mist eliminator must be raised

up and the bottom can be pulled toward the front of the

unit and removed.

Q-T

ENERGY RECOVERY VENTILATOR

(Option)

Before starting, make sure that the power has been

turned off. The return air grille panel must be removed.

The energy recovery ventilator (QERV) can be seen

after the panel has been removed. To gain access to

the mist eliminator, the QERV must be removed. See

Figure 23.

1. The front fill plate of the QERV must be removed.

There is one screw on either side of the plate.

Remove these screws and remove the plate.
2. On either side of the QERV there are mounting

screws that hold the QERV in place. Remove both

of these screws.
3. Underneath the heat recovery cassette there is a

power connector for the lower blower assembly. To

disconnect this plug, the tabs on both sides of the

plug must be squeezed to release the plug. While

squeezing the tabs, pull the plug out of the socket.
4. The QERV is plugged into the unit in the right side

of the unit. Both of these plugs must be disconnected

to remove the QERV. Squeeze the tabs on the sides

of the connector and pull straight out.
5. Slide the QERV assembly straight out of the unit,

being careful not to let the cassette slide out of the

QERV.
The mist eliminator can be seen through the opening in

the back of the unit. The mist eliminator must be raised

up and the bottom can be pulled toward the front of the

unit and removed.

Содержание Q-TEC Q24H2D Series













































Результаты поиска

Содержание Q-TEC Q24H2D Series

Отзывы:

Похожие инструкции для Q-TEC Q24H2D Series

Бренды по названию

Популярные бренды

Bard Q-TEC Q24H2D Series, Руководство по установке

Результаты поиска

Содержание Q-TEC Q24H2D Series

Отзывы:

Похожие инструкции для Q-TEC Q24H2D Series

Бренды по названию

Популярные бренды