Barco DP-1200 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 134

background image

10. Removal and installation of projector covers

10. REMOVAL AND INSTALLATION OF PROJECTOR

COVERS

About this chapter

Most maintenance and servicing procedures demand removing one or more of the projector covers to gain access to the parts to
maintain or to service. To avoid redundancy, all procedures about cover removing or installing are grouped together in this chapter.
The maintenance and servicing procedures also refer to this chapter if required. The procedures in this chapter describe, with
detailed step by step actions and illustrations, how to remove or install the projector covers. Note that some covers may only be
removed by quali

fi

ed service personnel, see remarks above each procedure.

W

ARNING

:

Always switch off the projector and unplug the power cord before removing one of the covers,

unless otherwise stated.

Overview

•

Removal of the lamp cover

•

Removal of the input cover

•

Removal of the front cover

•

Removal of the side cover

•

Removal of the rear cover

•

Removal of the top cover

•

Open the sealed compartment

•

Close the sealed compartment

•

Installation of the top cover

•

Installation of the rear cover

•

Installation of the side cover

•

Installation of the front cover

•

Installation of the input cover

•

Installation of the lamp cover

R59770242 DP-1200 06/01/2009

85

«
...
87
88
89
90
91
...
»

Содержание DP-1200







































































































































Отзывы:

Нет отзывов

Похожие инструкции для DP-1200

Бренд: Samsung Страницы: 32

Бренд: Samsung Страницы: 57

Бренд: Samsung Страницы: 2

Бренд: Dukane Страницы: 2

SmartCRYSTAL Pro

Бренд: Volfoni Страницы: 18

Бренд: Omnimount Страницы: 28

Бренд: Optoma Страницы: 50

Бренд: Optoma Страницы: 118

Бренд: Panasonic Страницы: 323

Бренд: Panasonic Страницы: 240

Бренд: Ask Proxima Страницы: 32

Бренд: Sony Страницы: 36

Бренд: Sony Страницы: 59

Бренд: Sony Страницы: 35

Бренд: Sony Страницы: 72

Бренд: Sony Страницы: 65

Бренд: Sony Страницы: 40

Бренд: Sony Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды