Barco DP-1200 Скачать руководство пользователя страница 112

Страница: 112 / 134

11. Maintenance

11.6 Authorization to clear security warning

When is an authorization required to clear the security warning?

If the Input & Communication unit has been removed or the sealed compartment has been opened an authorization will be required
to clear the security warning.

Necessary tools

•

Security key (Dallas iButton®).

•

Authorization pin code.

Authorization procedure to clear security warning

1. Ensure that the Input & Communication unit is properly installed.

2. Start up the projector (standby mode).

3. Initiate authorization by holding the security key in the security socket D..

Image 11-4

The color of the backlight of the numeric keys 1 to 10 of the local keypad changes from blue to yellow.

4. Enter pin code within 5 seconds. Maximum

ve (5) attempts permitted.

In case no keys are pressed, the color of the backlight of the numeric keys 1 to 10 changes back to blue.

In case of an

incorrect code

entry, the color of the backlight of the numeric keys 1 to 10 changes to

red

for 1 second and

than back to blue.

In case of a

correct code

entry, the color of the backlight of the numeric keys 1 to 10 changes to

green

for 1 second and

than back to blue.

Each attempt to clear the security warning and its result (successfully or unsuccessfully) is logged inside the
projector.

108

R59770242 DP-1200 06/01/2009

Содержание DP-1200







































































































































Результаты поиска

Содержание DP-1200

Отзывы:

Похожие инструкции для DP-1200

Бренды по названию

Популярные бренды

Barco DP-1200, Руководство по установке

Результаты поиска

Содержание DP-1200

Отзывы:

Похожие инструкции для DP-1200

Бренды по названию

Популярные бренды