Barco DP-1200 Скачать руководство пользователя страница 40

Страница: 40 / 134

4. Lamp & Lamp House

Image 4-11

3. Install the lamp cathode adaptor (A) upon the xenon bulb lamp (L) as illustrated. Use torque

2,5 Nm

(1,8 lbf*ft) to fasten the

xation screw (S) of the adapter. Use for that a torque wrench with a 5 mm Allen socket. Make sure that there is full contact

between the cathode adapter and the lamp base.

Note:

In case of a lamp replacement you have to reuse the adaptor from the xenon bulb lamp which you want to replace.

2,5 Nm

Image 4-12

4. Install the anode wire lug (L) upon the anode socket (S). Hold fast the nut N1 with an open-end wrench while fastening the nut

N2 with a torque of

9 Nm

(6,6 lbf*ft) using a torque wrench. Ensure that at both sides of the wire lug L a plane washer (W1 &

W2) is present.

Note:

The anode socket is located just below the UV blocker and can easily be removed from the lamp house. In case of a lamp
replacement you have to reuse the anode socket which is connected to the xenon bulb lamp which you want to replace.

R59770242 DP-1200 06/01/2009

Содержание DP-1200







































































































































Результаты поиска

Содержание DP-1200

Отзывы:

Похожие инструкции для DP-1200

Бренды по названию

Популярные бренды

Barco DP-1200, Руководство по установке

Результаты поиска

Содержание DP-1200

Отзывы:

Похожие инструкции для DP-1200

Бренды по названию

Популярные бренды