Barco DP-1200 Скачать руководство пользователя страница 120

Страница: 120 / 134

12. Convergence (with extenders)

Image 12-11

4. Slightly turn the green colored control knob number 6 until the green pattern in the upper right of the projected image converges

with the blue pattern.

Image 12-12

5. Repeat step 3 and 4 until coincidence is obtained of the green pattern in the lower left and upper right of the projected image.

6. Repeat from step 2 until full coincidence is obtained of the green pattern in the center, lower left and upper right of the projected

image.

7. Carefully secure the position of the DMD assembly by tightening the four convergence lock screws (reference 8 of image 12-9)

of the green channel. Fasten the screws crosswise and with small adjustments to each screw. Use a torque wrench with a 2,5
mm Allen socket and a torque of

0,6 Nm

(0,44 lbf*ft).

8. Close the sealed compartment and reinstall all covers of the projector.

116

R59770242 DP-1200 06/01/2009

Содержание DP-1200







































































































































Результаты поиска

Содержание DP-1200

Отзывы:

Похожие инструкции для DP-1200

Бренды по названию

Популярные бренды

Barco DP-1200, Руководство по установке

Результаты поиска

Содержание DP-1200

Отзывы:

Похожие инструкции для DP-1200

Бренды по названию

Популярные бренды