Barco DP-1200 Скачать руководство пользователя страница 101

Страница: 101 / 134

10. Removal and installation of projector covers

10.12 Installation of the front cover

The input cover and the lens may not be installed yet.

Necessary tools

7 mm

at screw driver.

How to install the front cover of the projector?

1. Check if the front

lter is present.

2. Ensure that no lens is mounted and that the input cover is not installed.

3. Install the front cover of the projector doing the following:

rst hook in the side of the front cover at the front

lter,

b) then gently push the other side of the front cover into position,
c) ensure that the locking studs in the corners click into their receivers.

Image 10-23

4. Secure the front cover by locking the captive screw in the middle at the bottom of the front cover.

Image 10-24

5. Reinstall the rubber dust ring around the lens holder. See detail at the right of image 10-24.

R59770242 DP-1200 06/01/2009

Содержание DP-1200







































































































































Результаты поиска

Содержание DP-1200

Отзывы:

Похожие инструкции для DP-1200

Бренды по названию

Популярные бренды

Barco DP-1200, Руководство по установке

Результаты поиска

Содержание DP-1200

Отзывы:

Похожие инструкции для DP-1200

Бренды по названию

Популярные бренды