System manual Coronis 1MP
81
BarcoMed software driver installation
If you have a single display configuration and you have enabled
DualView, Windows will not allow you to attach the second head.
This is normal and not a bug.
2. For the display which is still attached click on the
“Advanced”
Button.
3. Select the
“Adapter”
tab and then click on the
“List All Modes...”
button. Select the resolution and refresh rate that your Coronis
display supports from the dialog box and click
“OK”
.
Note:
In the Adapter box, the Adapter string shows if this display is
the First View or the Second View attached to the Display
Controller. Please make a note of this, so that you can arrange
the displays in the correct order later if necessary.
4. Click
“OK”
on the bottom of the Adapter Control Panel. If the
“OK”
button on the bottom of the Adapter Control Panel is not visible,
press the
“TAB”
key once and then press
“CTRL”+“Enter”
to
select
“OK
”.
5. Click
“OK”
in the “Windows will now apply your new desktop
settings” dialog box. Your Coronis display should now
synchronize and display the Windows desktop.
6. Click
“Yes”
when asked, “Your desktop has been reconfigured.
Do you want to keep these settings?”
To set the resolution of the second display attached to the BarcoMed
Display Controller you are working with, go back to the
“Settings”
tab of the “Display Properties Control Panel”. Attach the second
display you detached in step 2 above, by right clicking on the
rectangle that represents it and selecting “
Attached”
.
Now repeat steps 3-6 above for this display.
If you are using a Quad-Head Configuration repeat all of the above
steps for the two displays on the second display controller.
Tip:
After installing DualView and setting the resolutions in a Quad-
Head Configuration you may need to drag the heads into the proper
position in the window on the “Settings” tab, so that the arrangement
in the window on the “Settings” tab matches the physical
arrangement of your configuration.
Enabling or Disabling DualView
If you wish to either enable or disable DualView at a later time, you
may do so through the Monitor Configuration drop down menu on the
BarcoMed Driver tab. Please refer to the BarcoMed Driver Tab
chapter of this manual.
Содержание CORONIS 1MP
