manualshive.com logo in svg

Barco CORONIS 1MP, Системное руководство

Поделиться
Скачать
Barco CORONIS 1MP Скачать руководство пользователя страница 31

System manual Coronis 1MP

32

Using the USB hub

To use the display in a configuration controlled by MediCal Pro,
connect the display to the PC using the USB connector.
Also, the USB interface inside the display allows you to connect USB
devices, such as a keyboard, mouse or digital camera, to the display.

To use the USB hub:

1 Connect the display’s USB upstream connector (11) to the USB

port of the PC.

2 Connect any USB device to any of the display’s USB downstream

connectors (3) or (10).

Tilt and swivel positioning

Adjust the position of the panel for best viewing conditions.
The display foot allows adjusting the horizontal viewing angle, vertical
viewing angle and panel height.

Starting up

Proceed as follows:
1 Switch on the signal source (E.g., PC).
2 If necessary, select a suitable resolution or signal format for the

signal source.

 

Display installation

Содержание CORONIS 1MP


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды