Barbecook SPRING 2002, Руководство пользователя

Страница: 27 / 288

www.barbecook.com 27
6.5. Replace the gas bottle
1. Close the gas supply and set all control knobs to OFF.
2. Disconnect the empty gas bottle and connect the full gas
bottle.
3. Check the gas bottle, the hose, and all gas connections
for leaks. See “7. Checking for gas leaks”.
Note that when replacing the gas bottle, you must
always be well away from sources of ignition.
7. CHECKING FOR GAS LEAKS
7.1. Why check for gas leaks?
Propane and butane are both heavier than air. This means
that these gases will not drift away if they leak from the
appliance. On still days, leaked gas can accumulate in and
around the appliance and subsequently ignite and explode.
7.2. When to check for gas leaks?
• Before first use or after a lengthy period out of use.
Check that there are no gas leaks if the
appliance has been assembled by the supplier.
• You should you do this whenever you replace a gas part.
• At least once annually, ideally at the start of the season.
7.3. Safety instructions
• Place the appliance outside in a well-ventilated location.
Ensure that there are no flames or heat sources in the
vicinity of the appliance.
• Never use a lighter or matches to check for gas leaks.
• Do not smoke or ignite the burners when checking for gas
leaks.
7.4. What materials do I need?
To check for gas leaks, you require the following:
• A test fluid. You can use a ready-to-use leak spray or
mixture of water (50%) and dish soap (50%).
• The leak testing tool supplied with the appliance.
This fluid is used to suction up the test fluid and apply it to
the gas parts or gas connections that you want to check.
7.5. Check for gas leaks
You can check for gas leaks by applying a test fluid to all gas
parts and gas connections. If there are large bubbles on a
specific part or connection, there is a gas leak.
Proceed as follows to check for gas leaks:
1. Place the appliance outside.
2. Take the leak testing tool and test fluid (leak spray or water/
dish soap mix)
3. Open the lid and set all control knobs to OFF.
4. Open the gas supply slightly. To do this, turn the valve on
the gas supply just once.
5. Suction a small amount of test fluid with the leak testing tool
and apply it to the zone that you want to check.
The following parts must be checked:
• The weld seams on the gas bottle (A)
• The hose (B)
• The connections between the gas bottle and the pressure
regulator and between the pressure regulator and the hose (C)
• The connection between the hose and the appliance (D)
The pressure regulator and coupling on your
appliance may differ from the examples in the figures.
6. Proceed as follows:
• If you detect a leak, follow the instructions in “7.6 In the
event of a gas leak”.
• If there are no leaks, close the gas supply, rinse all parts
thoroughly with water, and dry them well.
7.6. In the event of a gas leak
1. Close the gas supply and proceed as follows:
• If you have detected a leak on one of the connections,
firmly tighten the connection in question.
• If you have detected a leak on the gas bottle or hose,
replace the gas bottle or hose.
2. Check the connection or part where you detected the leak
again.
3. If the leak has not been fixed, you must contact a
Barbecook dealer. You must not start using the appliance
until the leak has been fixed.
Consult www.barbecook.com or a list of
Barbecook dealers near you.
8. PREPARING THE APPLIANCE FOR USE
8.1. Before each use
Whenever you use the appliance, you must ensure that:
• The appliance is set up in a suitable location
See “3.3 Choosing a suitable location”.
• The hose does not drag over the ground and cannot come
into contact with hot surfaces or dripping fat.
• The bowl is clean. We recommend cleaning the bowl after
every use. See “11.2 Cleaning the bowl”.
• The burners and venturi tubes are not blocked by insect