Baker Hughes Consolidated 2700 Series Скачать руководство пользователя страница 42

Страница: 42 / 48

36 |

Baker Hughes

Problem

Possible Cause

Corrective Action

No action. The

valve does not go

into full lift.

Upper ring too high

A. Increase blowdown as outlined in Section

XV.C.4. of this manual.

Foreign material trapped between the disc

holder and the guide

Disassemble the valve and correct any

abnormality as outlined in Section XI.

of this manual. Inspect the system for

cleanliness.

Simmer

Lower ring too low

Adjust per Section XV.C.2. of this manual.

Steam line vibrations

Investigate and correct cause.

Valve leaking

and/or exhibiting

erratic popping

actions.

Damaged seat

A. Disassemble the valve, lap seating

surfaces, replace the disc if required, as

outlined in Section XIX.B. of this manual.

Part misalignment

Disassemble the valve, inspect contact

area of disc and nozzle, lower spring

washer or spindle, compression screw,

spindle straightness, etc.

Disc has insufficient rock

Disassemble the valve and check the disc

rock per Section XIX.E. of this manual.

Discharge stack binding on outlet

Correct as required.

Hangup, or the

valve does not

close completely.

Lower ring too high

A. Move the lower ring to the left one notch

per adjustment and test. Repeat until

problem is eliminated.

Foreign material

Disassemble the valve and correct any

abnormal condition. Inspect system for

cleanliness.

Excessive

blowdown

Upper ring too low

A. Decrease blowdown as outlined in Section

XV.C.3. of this manual.

Exhaust pressure too high

Decrease exhaust pressure by increasing

discharge stack area.

Chatter or short

blowdown

Upper ring too high

A. Lower upper ring.

Inlet piping pressure drop too high

Reduce inlet pressure drop to less than

one-half of required valve blowdown by

redesigning inlet piping.

Yoke vent is plugged

Clear the yoke vent.

XVI. Troubleshooting Consolidated Series 2700

Safety Valves

Содержание Consolidated 2700 Series














































Результаты поиска

Содержание Consolidated 2700 Series

Отзывы:

Похожие инструкции для Consolidated 2700 Series

Бренды по названию

Популярные бренды

Baker Hughes Consolidated 2700 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Consolidated 2700 Series

Отзывы:

Похожие инструкции для Consolidated 2700 Series

Бренды по названию

Популярные бренды