Bacharach 450 Скачать руководство пользователя страница 72

Страница: 72 / 86

Maintenance

ECA 450

Instruction 0024-9400

4.5 Replacing Internal Particulate Filter

An internal particulate filter is located at the inlet of the pump to protect the

pump in the event dirt is drawn into the analyzer’s GAS inlet. Under normal

operating conditions, the probe’s water trap / filter assembly should catch all

dirt particles large enough to damage the pump. But if the probe’s filter fails

or is disconnected, the internal particulate filter will provide backup

protection.

Do the following to replace the internal particulate filter:

Material Required:

• Medium Phillips screwdriver

• Replacement Internal Particulate Filter (refer to Section 6.1)

Procedure:

Turn off analyzer and remove screws from control panel.

Lift up front of control panel to gain access to the particulate filter

located on the right-hand side of the analyzer. See Figure 4-4.

Remove tubing from old filter; then discard filter.

Install tubing onto new filter, being sure to position the filter so that its

flow-arrow points toward the pump. Then reinstall control panel.

Figure 4-4. Replacing the Internal Particulate Filter

PARTICULATE FILTER

(Install with arrow pointing

toward inlet of pump)

Содержание 450























































































Результаты поиска

Содержание 450

Отзывы:

Bacharach 450, Инструкция по эксплуатации и обслуживанию, Страница: 72 / 86

Результаты поиска

Содержание 450

Отзывы: