Bacharach 450 Скачать руководство пользователя страница 57

Страница: 57 / 86

ECA 450

Calibration

Instruction 0024-9400

Wait until Measured reading on screen stabilizes. Then use the

∧∨

and

< > keys to enter an Applied value of 32 °F (0 °C).

Typical Calibrate TS-Zero Screen During Calibration:

   «CALIBRATE TS-ZERO««
   Measured       31°F
   Applied       032°F

Press

ENTER

to calibrate the analyzer’s Measured value to that of the

Applied value; after which the message “Good Calibration” should appear

followed by the CALIBRATE TS-SPAN screen.

TS-Span Procedure:

Adjust simulator to 572 °F (300 °C).

The calibration range is from 175 to 625 °F (79 to 329 °C). Any attempt to

calibrate outside this range will cause the message “Bad Calibration

Entry” to appear.

Wait until Measured reading on screen stabilizes. Then use the

∧∨

and

< > keys to enter an Applied value of 572 °F (300 °C).

Typical Calibrate TS-Span Screen During Calibration:

«CALIBRATE TS-SPAN««
Measured 560°F

Applied 572°F

Press

ENTER

to calibrate the analyzer’s Measured value to that of the

Applied value; after which the message “Good Calibration” should appear

followed by the Calibration List screen being redisplayed.

Remove calibration equipment.

3.6 Calibrate T-Air (Ambient Temperature) Channel

The following procedure first

zeros

and then

spans

the ambient-temperature

channel to known temperature values.

Material Required:

• Thermocouple Simulator (K-type) Range: 0 to 600 °F

Accuracy: ±0.5 °F

TA-Zero Procedure:

Adjust simulator to 32 °F (0 °C).

The calibration range is from 32 to 41 °F (0 to 5 °C). Any attempt to

calibrate outside this range will cause the message “Bad Calibration

Entry” to appear.

Содержание 450























































































Результаты поиска

Содержание 450

Отзывы:

Bacharach 450, Инструкция по эксплуатации и обслуживанию, Страница: 57 / 86

Результаты поиска

Содержание 450

Отзывы: