Bacharach 450 Скачать руководство пользователя страница 62

Страница: 62 / 86

Calibration

ECA 450

Instruction 0024-9400

3.10 Calibrate NO Sensor

The following procedure spans the optional Nitric Oxide sensor to a known

gas level.

Material Required:

• Calibration Gas Fixture (Section 3.2)

• Gas Cylinder: 250 ppm NO in Nitrogen (refer to Section 6.2)

Procedure:

Enter Calibration List screen; then choose NO per Section 3.3 to display

the CALIBRATE NO screen. A

t the conclusion of this step the pump

should be running.

Using the Gas Fixture shown in Figure 3-1, attach an NO calibration gas

cylinder to the analyzer’s GAS inlet port.

Adjust regulator of calibration fixture for a flow meter indication of

approximately 2 SCFH.

Wait until Measured reading on screen stabilizes (approximately

3 minutes). Then use the

∧∨

and < > keys to enter an Applied value that

equals the concentration stamped on the NO gas cylinder.

The calibration range is from 10 to 550 ppm. An applied value that is

outside this range will cause the message “Bad Calibration Entry” to

appear.

Typical Calibrate NO Screen During Calibration:

««««CALIBRATE NO««««

Measured 235 ppm
Applied 00250 ppm

Press

ENTER

to calibrate the analyzer’s Measured value to that of the

Applied value; after which the message “Good Calibration” should appear

along with the Calibration List screen being redisplayed.

If the message “Sensor Output Low” or “Sensor Not Calibrated” appears,

refer Section “5.4 Troubleshooting Guide.”

Turn off regulator; then remove gas cylinder from calibration fixture.

Содержание 450























































































Результаты поиска

Содержание 450

Отзывы:

Bacharach 450, Инструкция по эксплуатации и обслуживанию, Страница: 62 / 86

Результаты поиска

Содержание 450

Отзывы: