Bacharach 450 Скачать руководство пользователя страница 3

Страница: 3 / 86

ECA 450

Contents

Instruction 0024-9400

iii

Table of Contents

Introduction .................................................................................................................... 1

1.1

General Description ................................................................................................................................... 1

1.2

Features ..................................................................................................................................................... 1

1.3

Technical Data ............................................................................................................................................ 2

1.4

Operation Overview ................................................................................................................................... 5

1.5

Front Panel Connections and Controls ...................................................................................................... 6

1.5.1

GAS, PRESSURE, T-STACK (Probe) .............................................................................................. 6

1.5.2

T-AIR (Primary Air Thermocouple) ............................................................................................. 7

1.5.3

POWER (AC Adapter) ................................................................................................................. 7

1.5.4

∆

P REF (Differential Pressure) ................................................................................................... 7

1.5.5

RS232 (Computer Interface) ...................................................................................................... 7

1.5.6

OPT (Option) .............................................................................................................................. 7

1.6

Front Panel Keypad Controls ..................................................................................................................... 8

Operation ..................................................................................................................... 11

2.1

Turning On the Analyzer .......................................................................................................................... 11

2.2

Turning Off the Analyzer .......................................................................................................................... 11

2.3

Fuel Selection ........................................................................................................................................... 12

2.4

Performing a Combustion Test ................................................................................................................ 13

2.5

Ending a Combustion Test ....................................................................................................................... 15

2.6

Performing a Draft Measurement ........................................................................................................... 15

2.7

Saving Test Data ....................................................................................................................................... 16

2.8

Clearing Memory ..................................................................................................................................... 16

2.9

Recalling Test Data Stored in Memory ..................................................................................................... 17

2.10

Printing Data ............................................................................................................................................ 19

2.11

Downloading Data to a Personal Computer ............................................................................................ 20

2.12

Data Logging ............................................................................................................................................ 22

2.12.1

Turning Data Logging On .......................................................................................................... 22

2.12.2

Turning Data Logging Off ......................................................................................................... 24

2.13

Importing Saved Data Into a Spreadsheet ............................................................................................... 25

2.14

Primary Air Temperature Measurement ................................................................................................. 27

2.14.1

Thermocouple Method ............................................................................................................ 27

2.14.2

Probe Thermocouple Method ................................................................................................. 27

2.14.3

Thermometer Method ............................................................................................................. 29

2.14.4

Internal Temperature Sensor Method ..................................................................................... 30

2.15

Differential Pressure Measurement ........................................................................................................ 31

2.16

Statistics Mode......................................................................................................................................... 32

2.17

Setting Up the Analyzer ........................................................................................................................... 35

2.17.1

Temperature Units ................................................................................................................... 36

2.17.2

Pressure Units .......................................................................................................................... 36

2.17.3

Pollution Units ......................................................................................................................... 36

2.17.4

Language .................................................................................................................................. 37

2.17.5

Date .......................................................................................................................................... 37

2.17.6

Time ......................................................................................................................................... 38

2.17.7

Reference ............................................................................................................................ 38

2.17.8

Test ID ...................................................................................................................................... 39

2.17.8.1

Enter / Edit Test ID Information ......................................................................... 39

2.17.8.2

Select Test ID ...................................................................................................... 40

2.17.8.3

Transmit Test ID.................................................................................................. 41

2.17.8.4

Clearing Test ID Information .............................................................................. 42

2.17.9

Display Timeout ....................................................................................................................... 43

2.17.10

Display Format ......................................................................................................................... 43

2.17.10.1

Changing Display Format .................................................................................... 44

Содержание 450























































































Результаты поиска

Содержание 450

Отзывы:

Bacharach 450, Инструкция по эксплуатации и обслуживанию, Страница: 3 / 86

Результаты поиска

Содержание 450

Отзывы: