46
47
6.6 Removing the fabric cover
6.6.1 Removing the cover of the headrest
A) Removing the 5-point harness
Take off the cover from backrest and base.
B) Headrest
1. Move the headrest of the child seat to the upper position.
2. Take off the cover from belt holder of headrest first,then remove the cover of the
headrest.
6.6.2 Re-fitting the Cover Simply follow the steps in the opposite way.
CAUTION! Never use the child seat in installation without a correct installedbuckle.
Make sure that the metal plate is correctly attached.
CAUTION! Check that the harness straps are not twisted and that they have been
correctly inserted in the belt slots on the cover.
6.7 Adjust the angle of child safety car seat There has 4-level adjustment in the child
safety car seat.
Before fixing a child in the child restraint system,the seat must be set on the recline
position for rear-facing use,see picture or in the siting position for forward-facing
use, see picture.
To incline the safety seat, grab the handle located between the safety seat and base,
and set in a required position. To adjust the lying position, press the rotation button,
turn the safety seat by 180° and then set the lying position of the backrest. The
second level is intended for children whose
weight is 15-36 kg, while the third level 9-18kg.
To achieve that,use the recline handle located in front of the child restraint system
between the sitting part and the base to adjust the desired position.
instruction
instruction
6.5 Removing 5-point harness
6.5.1 Loosen the 5-point harness of the child
seat as much as possible by press the button of
the crotch belt.
6.5.2 Turn the baby safety car seat to back,
unzip the seat cover.
6.5.3 Loosening the shoulder belt in order to
access the metal link and connector at the
back of the child seat, remove the belt from
connector,then remove the shoulder belt from
metal link.follow step ①②③,④⑤
6.5.4 Then from the front of the child seat, pull
out shoulder belt through the slots.
6.5.5 Pull below both,the shoulder pads and the
belts to the front through the slots. (Front side
of the child seat).
6.5.6 Remove the shoulder pads from the
shoulder belts and put them in the storage bag.
6.5.7 Roll the shoulder belts and place them
separately on both side into the fabric cover
from the slot of fabric.
0-36kg
instruction
instruction
6.6 Removing the fabric cover
6.6.1 Removing the cover of the headrest
A) Removing the 5-point harness
Take off the cover from backrest and base.
B) Headrest
1. Move the headrest of the child seat to the
upper position.
2. Take off the cover from belt holder of
headrest first,then remove the cover of the
headrest.
6.6.2 Re-fitting the Cover
Simply follow the steps in the opposite way.
CAUTION!
Never use the child seat in installa-
tion without a correct installed buckle.
Make sure that the metal plate is correctly
attached.
CAUTION!
Check that the harness straps are not
twisted and that they have been correctly
inserted in the belt slots on the cover.
6.7 Adjust the angle of child safety car seat
There has 4-level adjustment in the child
safety car seat.
Before fixing a child in the child restraint
system,the seat must be set on the recline
position for rear-facing use,see picture ④ or in
the siting position for forward-facing use,see
picture①②③
To achieve that,use the recline handle
located in front of the child restraint system
between the sitting part and the base to
adjust the desired position.
Total has four level positions:
①first level ②second level
③third level ④ the fourth level
0-36kg
6.5.8 Grasp the metal plate from underneath
and turn it into a vertical position.Push
upwards and slide the metal plate through
the slot.
6.5.9 Remove the harness buckle with the
crotch pad and store it in the storage bag.
Tylko przodem
do kierunku jazdy
Tylko przodem
do kierunku jazdy
Tylko przodem
do kierunku jazdy
Tylko tyłem
do kierunku jazdy
– Then from the front of the child seat, pull out shoulder belt through the slots.
– Pull below both,the shoulder pads and the belts to the front through the slots.
(Front side of the child seat).
– Remove the shoulder pads from the shoulder belts and put them in the storage
bag.
6.5.7 Roll the shoulder belts and place them separately on both side into the fabric
cover from the slot of fabric.
– Grasp the metal plate from underneath and turn it into a vertical position. Push
upwards and slide the metal plate through the slot.
– Remove the harness buckle with the crotch pad and store it in the storage bag.
