manualshive.com logo in svg

Baby Lock Pro-Stitcher Premium BLPS6, Руководство по установке

Поделиться
Скачать
Baby Lock Pro-Stitcher Premium BLPS6 Скачать руководство пользователя страница 9

3.2  |  BLPS6 - CJ   Installation Guide

www.babylock.com

Optional U.S. Grounding

This product is for use on a nominal 120 V or nominal 220 V circuit, and has a grounding plug that 

looks like the plug illustrated in sketch A above. A temporary adapter, which looks like the adapter 

illustrated in sketches B and C, may be used to connect this plug to a 2-hole receptacle as shown 

in sketch B if a properly grounded outlet is not available. The temporary adapter should be used 

only until a properly grounded outlet can be installed by a qualified electrician. The green colored 

rigid ear, lug, and the like, extending from the adapter, must be connected to a permanent ground 

such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in 

place by the metal screw.

 

 

Â

IMPORTANT:

 In Canada, the use of a temporary adapter is not permitted by the Canadian 

           Electric Code.

Pro-Stitcher Parts List for Baby Lock Crown Jewel

 

NOTE:

 The parts photographed in this manual may look different from the ones you 

received.

A. Blue X-axis Flexirack (12 feet)

B. X-axis Flexirack clamps and screws

C. 3/32-inch drill bit

  ITEM       

 

 

 

 

 

 

  QUANTITY  

 

PHOTO

1

4

1

GROUNDED OUTLET BOXES

METAL

SCREW

TAB FOR

GROUNDING

SCREW

Содержание Pro-Stitcher Premium BLPS6

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды