manualshive.com logo in svg

Baby Lock Pro-Stitcher Premium BLPS6, Руководство по установке

Поделиться
Скачать
Baby Lock Pro-Stitcher Premium BLPS6 Скачать руководство пользователя страница 29

6.4  |  

BLPS6 - CJ   Installation Guide

www.babylock.com

Problem / Symptom

Corrective Measure

Jumps between repeated patterns

Use  of  any  of  the  Repeat  options  results  in                

a jump between each pattern.

When using the Repeat functions, if the start and/or 

stop points are within the block of the pattern (i.e. they 

are not located at the left and right-hand sides of the 

pattern block) there will be a jump between each repeat 

of the pattern. This can be corrected by selecting the 

Point 2 Point button. If the start and end points are at 

different heights, the design will have to be modified 

using design editing software to put them at the same 

height to prevent the jump.

No patterns or folders show up in the design library

The current path is pointing to the wrong  

drive letter.

Designs are stored on the computer’s hard drive and 

on the removable USB flash drive. If you are attempting 

to access designs specifically on the USB flash drive, 

make sure the USB flash drive is plugged in securely 

to one of the side USB ports on the black box behind 

the tablet computer. Press Cancel if the Open screen is 

already open, insert the USB flash drive, wait about 15 

seconds, and then press the Open button again.  

The patterns that come pre-loaded on the Baby Lock 

USB Flash drive are located in a folder called Designs 

on the USB flash drive (usually drive D:\ or E:\). From 

the Open window, select a drive letter by pressing on 

the arrow button next to the drive you wish to browse. If 

there is a circle with a ^ symbol on the right-hand side 

of the button, it means there are more folders in that 

particular path.

If there continues to be nothing showing up on the USB 

flash drive, plug it into a desktop or laptop computer 

and verify that the USB flash drive has the desired files 

on it. If the computer says it wants to reformat the flash 

drive then the flash drive has failed and will need to be 

replaced. If it opens but there are no files on the flash 

drive, contact Baby Lock for replacement files.*

*

 Baby Lock highly recommends backing up all 

pattern files on a home computer or another disk.

Содержание Pro-Stitcher Premium BLPS6

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды