manualshive.com logo in svg

Baby Lock Pro-Stitcher Premium BLPS6, Руководство по установке

Поделиться
Скачать
Baby Lock Pro-Stitcher Premium BLPS6 Скачать руководство пользователя страница 15

3.8  |  

BLPS6 - CJ   Installation Guide

www.babylock.com

Y-encoder circuit board replacement

 

Â

IMPORTANT:

 This step is required 

only

 if the circuit board on the Y-encoder is blue. If the 

Y-encoder has a black circuit board, skip ahead to the next step.

Replace the Y-encoder circuit board with the one in the package (

see Parts List, item G

) if the 

circuit board is blue and does not have a 3-pin connector attached. It is held in place with one 

screw and five connecting pins.

To replace the Y-encoder

1.  Unplug the stitch regulator cable from the Y-encoder. 

2.  Remove the screw that holds the circuit board in 

place with a small Phillips screwdriver.

3.  Gently pull the circuit board outward toward the front of the quilting machine (the same 

direction the screw came out). 

Replace this style  

Y-encoder circuit board.

This style Y-encoder circuit board does 

not need to be replaced.

Содержание Pro-Stitcher Premium BLPS6

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды