manualshive.com logo in svg

Baby Lock Pro-Stitcher Premium BLPS6, Руководство по установке

Поделиться
Скачать
Baby Lock Pro-Stitcher Premium BLPS6 Скачать руководство пользователя страница 20

www.babylock.com

BLPS6 - CJ   Installation Guide

  |  3.13

To attach the tablet computer

1.  Disconnect the front handlebar cable from the side of the machine’s head. Then remove the 

handlebars from the front of the quilting machine by removing the three hex-head bolts with a 

5mm Allen wrench. 

 

If you’re having difficulty reaching the front handlebar cable, first remove two of the hex-head 

bolts and loosen the third bolt. Then, rotate the handlebar slightly to provide easier access to 

the handlebar cable.

2.  Make sure the three handlebar bolts are in the 

front handlebar and protruding out the bottom of 

the handlebar. 

3.  Position the handlebar over the computer bracket 

such that the screws go through the three holes 

in the bracket. 

4.  Secure the handlebar and bracket in place on the machine head using the three                          

handlebar bolts. 

Содержание Pro-Stitcher Premium BLPS6

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды