B. Braun 871 5416 Скачать руководство пользователя страница 18

Страница: 18 / 86

System Overview

1 - 8

Infusomat® fmS 2.3 gb

In mains operation battery function is checked during the switch-

on test. Therefor the charge and discharge current are measured

and the charging of the battery is interrupted for the duration of

measurement.

Battery Operation

The battery function is monitored by the following data: charge

current, discharge current and time, and self-discharge time. In

battery operation the battery function is checked during switch-

on test. The theoretical load condition is read from the clock mod-

ule of the battery. Then the battery is connected to UPS and the

voltage is measured. If the minimum requirements are not

reached a battery alarm is activated.

Alarm Circuit

The alarm generation consists of:

Standstill of pump due to switch-off of MS (motor circuit)

and UMOT (motor operating voltage)

Audible alarm due to the drive via ALA-AK (control channel)

or via ALA-UB. The alarm volume is about 65dBA.

Optical alarm. Is displayed in the LCD- and a separate LED-

display. Additionally the set rate flashes with AAA.A.

Staff call via the MFC staff call cable.

The user must check the optical and audible alarm during the

switch-on test. An alarm must be activated to test the staff call

alarm of the Infusomat® fmS, e.g. open pump cover during oper-

ation.

Pump Unit

The pump head is driven by a stepper motor. Each full step of the

motor is realized by 5 microsteps. The motor is driven by an FET

output stage. The function processor controls the motor with the

MS signal. A slot disc which is mounted on the pump head axle is

scanned by two light barriers (PKS1 and PKS2 signal). Thereby the

control microprocessor monitors the direction of rotation and

speed of the pump head.

The pump head position is also determined with the PKS2 signal.

The motor can therefore be accelerated during the withdrawal

phase. Thus a nearly pulse-free flow is realized in the lower deliv-

ery range (<100 ml/h). The total pump head cycles and running

time are available in the Service Program under history data.

Содержание 871 5416























































































Результаты поиска

Содержание 871 5416

Отзывы:

Похожие инструкции для 871 5416

Бренды по названию

Популярные бренды

B. Braun 871 5416, Руководство по обслуживанию

Результаты поиска

Содержание 871 5416

Отзывы:

Похожие инструкции для 871 5416

Бренды по названию

Популярные бренды