Avid Technology 9320-65044-00, Руководство пользователя

Страница: 141 / 186

Chapter 11: Normal Mode Operations and Commands 135
To change a previously assigned insert or send on a flipped
encoder:
1
On the channel where you want to change the assignment,
press the Inserts or Sends switch to display the corresponding
elements on the channel.
2
Press and hold the channel Select switch for the flipped in-
sert or send you want to change, until the channel scribble
strip shows a right arrow (“>”) next to the assignment to indi-
cate the channel is in assign mode.
3
Do one of the following to select a new insert or send:
• Move the channel fader to select from the current level of
menu choices.
– or –
• Press the channel Select switch to move down and the
channel Mute switch to move up through menu levels.
4
When the new insert or send is displayed in the channel
scribble strip, do one of the following:
• Press the flashing channel Select switch to confirm the
assignment.
– or –
• Press the flashing Escape switch to cancel the assign-
ment.
To remove an individual insert or send on a flipped encoder:
1
On the channel where you want to remove the assignment,
press the Inserts or Sends switch to display the corresponding
elements on the channel.
2
Press and hold the channel Select switch for the flipped in-
sert or send you want to remove, until the channel scribble
strip shows a right arrow (“>”) next to the assignment to indi-
cate the channel is in assign mode.
3
Press the encoder Bypass/Mute/Pre switch repeatedly until
you reach the top level menu for the assignment.
4
Move the channel fader until no assignment is visible.
5
Do one of the following:
• Press the flashing channel Select switch to confirm the
removal.
– or –
• Press the flashing Escape switch to cancel the removal
and restore the assignment.
Inline Console Mode
With Inline mode, you can control an input channel and its
corresponding monitor channel from a single channel strip on
D-Control.
An input signal (for example, from a Digidesign PRE) is
brought into an Auxiliary Input track, and routed to an Audio
track for recording and monitoring. Inline mode on D-Control
is then used to control each of these elements from a single
channel strip: the PRE and Auxiliary Input level controls are
controlled with the channel strip encoders, and the record
track levels are controlled with the channel strip fader.
To control an Auxiliary Input track and Audio track from a single
D-Control channel strip:
1
Assign the output of a Digidesign PRE (optional) or other au-
dio source to an Auxiliary Input track.
2
Assign the output of the Auxiliary Input track to an Audio
track.
3
On D-Control, press the Input switch in the Channel Strip
Mode controls for the Audio channel.
4
On the Audio channel, press the encoder Select switch on the
lowest row of encoders and turn the encoder knob to select the
Auxiliary Input track.
5
Press Select to confirm the choice.
The controls for the PRE and the Auxiliary Input appear on
the Audio channel’s rotary encoders as follows, from top to
bottom:
• Encoder 1 Knob/Switch: PRE Phantom Power
• Encoder 2 Knob/Switch: PRE Polarity
• Encoder 3 Knob/Switch: PRE Impedance/Pad
• Encoder 4 Knob/Switch: PRE Source/Insert
• Encoder 5 Knob/Switch: PRE Gain/HPF
• Encoder 6 Knob/Switch: Aux Gain/Aux Mute
6
(Optional) Hide the Auxiliary Input channels using the
Show/Hide Soft Keys.
7
Adjust the PRE gain using Encoder 5.
8
Fine tune the input gain by adjusting the Auxiliary Input
level using Encoder 6 (the bottom encoder).
9
Press the Sends switch in the Channel Strip Mode controls
and configure any cue mixes or effects sends for the channel.
10
Adjust the monitoring level with the Audio channel fader.
To view a hidden Auxiliary Input channel while in Inline mode:

Press Control (Windows) or Command (Macintosh) and
press the encoder Select switch on Encoder 6.
The Auxiliary Input channel is focused in the Focus Channel
strip.