Aviation Models 30% Extra 260 Скачать руководство пользователя страница 21

 

21 

 

 
 
 
 
 
 
 
 
 
 

 

Control Throws 

 

Here are some starting points for the control throws.    

Do not use the 3d settings 

until you are thoroughly familiar with the plane on low rates.  The 3D rates if 
pulled hard at moderately high speed will cause the plane to stall, tumble, and 
hunt for dirt. 

 

High rate(3D)    

 

 

Low rate 

Ailerons  

 

 

30+ deg  

 

 

 

 

18 deg 

Elevators    

 

40+ deg.  

 

 

 

 

18 deg. 

Rudder  

 

 

45 deg.  

 

 

 

 

25 deg

 
Fly the plane on low rates at first.  The 3d rates are intended 
only for extreme aerobatics.  If you are in doubt about your 
skills, ask a skilled aerobatic pilot to help you with a trainer 
cord.

 

 
 

Thanks for Purchasing our 30% Extra 260.  We hope it provides you with 

many hours of enjoyment.  Good luck! 

Sammy 

6.5” 

Make sure the plane balances at 
6.5”.  You will probably find this 
to be a bit nose heavy, but it 
should be safe.  If the plane were 
to take off tail heavy, it may be 
uncontrollable.  After 2 or 3 trim 
flights, you can move the CG 
back 1/8 ” at a time.  It flies much 
better once the CG is just right.  
You can also log on to one of the 
popular RC bulletin boards.  
There you can find where other 
pilots have put the CG on their 
Extra 260. 

Содержание 30% Extra 260






















Отзывы: