Aviation Models 30% Extra 260 Скачать руководство пользователя страница 2

 

Warranty Information: 

 

Aviation Models, Inc. guarantees this kit to be free of defects in both material and 
workmanship at the time of purchase. This warranty does not cover any components 
damaged by use or modification. In no case shall Aviation Models, Inc. liability ex-
ceed the original cost of the purchased kit.  
 
Further, Aviation Models, Inc, reserves the right to change or modify this warranty 
without notice.  In that Aviation Models has no control over final assembly or materi-
als used in final assembly, no liability shall be assumed or accepted for any damage 
resulting from the use by user of the final user assembled product.  By the act of using 
the user assembled product, the user accepts all resulting liability.  The user should 
check the aircraft for structural damage before each flying session and immediately 
after any ground strike other than a soft landing.  DO NOT ATTEMPT TO FLY AN 
AIRCRAFT WITH ANY STRUCTURAL DAMAGE! 
 
If the buyer is not prepared to accept the liability associated with the use of this prod-
uct, the buyer is advised to return this kit immediately in new and unused condition to 
the place of purchase. 
 
While this kit has been flight tested to exceed normal use, if the plane will be used for 
extremely high stress flying such as racing or extreme aerobatics the modeler is re-
sponsible for taking steps to reinforce the high stress points.  If you do not feel confi-
dent to do this, seek advice from experienced modelers. 
 
This model should never be operated in a manner that is not compliant with all of the 

Academy of Model Aeronautics  National Model Aircraft Safety Codes.

 

 

 

Read through this manual before starting construc-
tion. It contains important warnings and instructions 
concerning the assembly and use of this model. 

 

The pictures in this manual may be of airplanes with different covering schemes.  
The planes pictured were of identical construction.  Only the color schemes were 
different.

Содержание 30% Extra 260






















Отзывы: