Avaya P334T Скачать руководство пользователя страница 89

Страница: 89 / 182

Chapter 6

CLI – Layer 2

Avaya P334T User’s Guide

show ppp incoming timeout

Use the

ppp incoming timeout

command to see the amount of time in minutes

that a PPP session can remain idle before being automatically disconnected.

The syntax for this command is:

show ppp incoming timeout

Output Example:

P330-N> show ppp incoming timeout

PPP incoming timeout is 10 minutes

show ppp baud-rate

Use the s

how ppp baud-rate

command to display the set baud-rate.

The syntax for this command is:

show ppp baud-rate

Output Example:

P330-N> show ppp baud-rate

PPP baud rate is 38400

show ppp configuration

Use the s

how ppp configuration

command to display the ppp configuration

The syntax for this command is:

show ppp configuration

Output Example:

P330-N> show ppp configuration

PPP baud rate is 38400

PPP incoming timeout is 0 minutes

PPP Authentication Parameters:

------------------------------

Incoming: None

Содержание P334T























































































































































































Результаты поиска

Содержание P334T

Отзывы:

Avaya P334T, Руководство пользователя, Страница: 89 / 182

Результаты поиска

Содержание P334T

Отзывы: