Avaya P334T Скачать руководство пользователя страница 51

Страница: 51 / 182

Chapter 5

Avaya CLI – Architecture, Access & Conventions

Avaya P334T User’s Guide

Entering the CLI

To enter the CLI, enter your username and password. Your access level is indicated
in the prompt as follows:
The User level prompt is shown below:

P330-N>

The Privileged level prompt is shown below:

P330-N#

The Configure level prompt for Layer 3 configuration is shown below:

P330-N(configure)#

The Supervisor level prompt is shown below:

P330-N(super)#

Entering the Technician Level

This level is can only be accessed from the Privileged and Supervisor levels not from
the User level.
This feature is not documented and is for use by Avaya Technical Support only.

Conventions Used

The following conventions are used in this chapter to convey instructions and
information:
•

Mandatory keywords are in boldface.

•

Variables that you supply are in pointed brackets <>.

•

Optional keywords are in square brackets [].

•

Alternative but mandatory keywords are grouped in braces {} and separated by
a vertical bar |.

•

If you enter an alphanumeric string of two words or more, enclose the string in
inverted commas.

•

Information displayed on screen is displayed in

text

font.

Содержание P334T























































































































































































Результаты поиска

Содержание P334T

Отзывы:

Avaya P334T, Руководство пользователя, Страница: 51 / 182

Результаты поиска

Содержание P334T

Отзывы: