Avaya P334T Скачать руководство пользователя страница 109

Страница: 109 / 182

Chapter 6

CLI – Layer 2

Avaya P334T User’s Guide

The protocol has been set to TIME protocol

set time server

The

set time server

command is used to set the TIME server address.

The syntax for this command is:

set time server <ip>

set time client

The

set time client

command is used to enable or disable the periodic

network time acquisition by the switch from the network time server (SNTP or
TIME protocol).

The syntax for this command is:

set time client <enable|disable>

set ip route

Use the

set ip route

command to add IP addresses to the IP routing table. You

can configure from one to ten (10) default gateways for a P330 stack.

The syntax for this command is:

set ip route <destination> <gateway>

Output Example:
This example shows how to add a default route to the IP routing table:

P330-N# set ip route

0.0.0.0

192.168.1.1

destination = 0.0.0.0 gateway = 192.168.1.1

ROUTE NET TABLE

destination gateway flags Refcnt Use Interface

------------------------------------------------------------------------

0.0.0.0 192.168.1.1 1 1 3199 se0

127.1.1.0 127.1.1.1 1 8 7606 se1

------------------------------------------------------------------------

IP address of the TIME server.

destination

IP address of the network, or specific host to be added

gateway

IP address of the router

Содержание P334T























































































































































































Результаты поиска

Содержание P334T

Отзывы:

Avaya P334T, Руководство пользователя, Страница: 109 / 182

Результаты поиска

Содержание P334T

Отзывы: