manualshive.com logo in svg

Avaya P334T, Руководство пользователя, Страница: 114 / 182

Поделиться
Скачать
Avaya P334T Скачать руководство пользователя страница 114

Chapter 6

CLI – Layer 2

98

Avaya P334T User’s Guide

set interface ppp

Use the set interface ppp command to configure the P330 PPP interface IP 
parameters, exit modem mode, disconnect the PPP session, or reset the connected 
modem.
A PPP connection can be established only after the P330 is configured with an IP 
address and net-mask. The IP address is a dummy address that is shared between 
two peers, and must be taken from a subnet that is different from the agent’s IP sub-
net. 

The syntax for this command is:

set interface ppp <ip_addr><net-mask>

Output Example:

P330-N> set interface ppp 149.49.34.125 255.255.255.0

Interface ppp has its ip address set 

You can also use the 

set interface ppp

 command to enter modem mode, enter 

terminal mode, disconnect the PPP session or to reset the connected modem.
The syntax for this command is:

set interface ppp {enable|enable-always|disable|off|reset}

Output Example:

P330-N> set interface ppp reset

PPP has reset the connected modem.

ip_addr

IP address used by the P330 to connect via its PPP interface

net-mask

Subnet mask used by the P330 to connect via its PPP interface

enable

Enable PPP and enter modem mode.

enable-always

Enable automatic reentry into modem mode after modem cable 
disconnection or reconnection.   

disable

Disable PPP and enter terminal mode

off

Disconnect the active PPP session.

reset

Reset the connected modem.

Содержание P334T























































































































































































Отзывы:

Нет отзывов