Avaya P334T Скачать руководство пользователя страница 125

Страница: 125 / 182

Chapter 6

CLI – Layer 2

Avaya P334T User’s Guide

109

set port mirror

Use the

set port mirror

command to define a port mirroring source-

destination pair in the stack.

The syntax for this command is:

set port mirror source-port <mod_num>/<port_num> mirror-port

<mod_num>/<port_num> sampling {always|disable} direction

{rx|tx|both}

Output Example:

P330-N# set port mirror source-port 1/9 mirror-port 1/10

sampling always direction both

Mirroring both Rx and Tx packets from port 1/9 to port 1/10 is

enabled

set port spantree

Use the

set port spantree

command to enable or disable the spanning tree

mode for specific switch ports.

The syntax for this command is:

set port spantree {enable|disable} [module/port]

Output Example:
Enable the spanning tree mode for port 2 on module 3.

P330-N# set port spantree enable 3/2

always

Keyword to activate the port mirroring entry

disable

Keyword to change the status of the port mirroring entry to “not active”

Keyword to copy only incoming traffic

Keyword to copy only outgoing traffic

both

Keyword to copy both incoming and outgoing traffic

enable|disable

Enables or disables the spanning tree mode for the
specified ports.

module/port

The switch/port number.

Содержание P334T























































































































































































Результаты поиска

Содержание P334T

Отзывы:

Avaya P334T, Руководство пользователя, Страница: 125 / 182

Результаты поиска

Содержание P334T

Отзывы: