Avaya P334T Скачать руководство пользователя страница 150

Страница: 150 / 182

Chapter 6

CLI – Layer 2

134

Avaya P334T User’s Guide

set radius authentication retry-time

Use the

set radius authentication retry-time

command to set the time

to wait before re-sending an access request.

The syntax for this command is:

set radius authentication retry time <time>

set radius authentication retry-number

Use the

set radius authentication retry-number

command to set the

number of times an access request is sent when there is no response.

The syntax for this command is:

set radius authentication retry number <number>

set radius authentication udp-port

Use the

set radius authentication udp-port

command to set the RFC

2138 approved UDP port number. Normally, the UDP port number should be set to
its default value of 1812. Some early implementations of the RADIUS server used
port number 1645.

The syntax for this command is:

set radius authentication server udp-port <number>

time

Retry time in seconds

number

Retry number

Содержание P334T























































































































































































Результаты поиска

Содержание P334T

Отзывы:

Avaya P334T, Руководство пользователя, Страница: 150 / 182

Результаты поиска

Содержание P334T

Отзывы: