Avaya P334T Скачать руководство пользователя страница 104

Страница: 104 / 182

Chapter 6

CLI – Layer 2

Avaya P334T User’s Guide

Set Commands Summary Table

Following is a Table of the Privileged Level

set

commands.

• set logout

Sets the number of minutes before an
inactive CLI session automatically logs
out.

Page 91

• set timezone

Sets the timezone for the system.

Page 92

• set time protocol

Sets the time protocol for use in the
system.

Page 92

• set time server

Sets the NTP server address.

Page 93

• set time client

Enables or disables the time client.

Page 93

• set ip route

Adds IP addresses to the IP routing
table.

Page 93

• set snmp community

Sets the SNMP community string for a
specific switch.

Page 94

• set snmp trap

Sets the SNMP trap of the system or
add/delete an entry into/from the
SNMP trap receiver table.

Page 94

• set snmp trap auth

Enables/disables the SNMP
authentication trap.

Page 95

• set snmp retries

Sets the number of SNMP retries.

Page 95

• set snmp timeout

Sets the SNMP timeout.

Page 96

• set system location

Sets the system location.

Page 96

• set system name

Sets the system name.

Page 96

• set system contact

Sets the system contact person.

Page 96

• set device-mode

Sets the basic mode of operation.

Page 97

• set interface

Configures the management interface of
the device.

Page 97

• set interface ppp

Configures the device ppp interface.

Page

• set port level

Sets the priority level of a port.

Page 99

• set port negotiation

Sets the auto negotiation mode of a port.

Page 99

• set port enable

Administratively enables a port.

Page 100

Содержание P334T























































































































































































Результаты поиска

Содержание P334T

Отзывы:

Avaya P334T, Руководство пользователя, Страница: 104 / 182

Результаты поиска

Содержание P334T

Отзывы: