Avaya P334T Скачать руководство пользователя страница 68

Страница: 68 / 182

Chapter 6

CLI – Layer 2

Avaya P334T User’s Guide

show port classification

Use the

show port classification

command to display a port’s classification.

The syntax for this command is:

show port classification [module/[port]

Output Example:

P330-1(super)# show port classification

Port Port Classification

------ ---------------------

1/1 regular

1/2 regular

1/3 regular

1/4 regular

1/5 regular

1/6 regular

1/7 regular

etc...

show port redundancy

Use the

show port redundancy

command to display information about all

redundancy schemes defined for this stack.

The syntax for this command is:

show port redundancy

Output Example:

P330-N> show port redundancy

Redundancy Name Primary Port Secondary Port Status

----------------- -------------- ---------------- --------

uplink 1/7 2/12 enable

module/port

The switch number/the port number

Содержание P334T























































































































































































Результаты поиска

Содержание P334T

Отзывы:

Avaya P334T, Руководство пользователя, Страница: 68 / 182

Результаты поиска

Содержание P334T

Отзывы: