Avaya P334T Скачать руководство пользователя страница 137

Страница: 137 / 182

Chapter 6

CLI – Layer 2

Avaya P334T User’s Guide

121

Output Example:

P330-N# set arp-tx-interval 15

ARP tx interval was set to 15 seconds.

set self-loop-discovery Admin_Status

Use the

set self-loop-discovery Admin_Status

command to enable or

disable IBM token ring discovery feature at the module level.

Note:

You must disable Spanning Tree before you can enable self-loop-discovery.

Note:

This command is not supported by the P332G-ML and P332GT-ML switches.

The syntax for this command is:

set self-loop-discovery Admin_Status <enable|disable>

Example:

P330-N# set self-loop-discovery Admin_Status enable 1

Self-Loop-Discovery is disabled on module 1.

set welcome message

Use the

set welcome message

command to set a welcome message to appear

after a reboot or after opening a new session (see

session

command) in the stack.

The syntax for this command is:

set welcome message [string]

Output Example:

P330-N# set welcome message avaya

The new welcome string is “avaya”

string

string -

The string to be used as the welcome message.

blank -

Restores the default string.

Содержание P334T























































































































































































Результаты поиска

Содержание P334T

Отзывы:

Avaya P334T, Руководство пользователя, Страница: 137 / 182

Результаты поиска

Содержание P334T

Отзывы: