Avaya DEFINITY SERIES Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 101

Avaya DEFINITY SERIES Скачать руководство пользователя страница 85

DEFINITY Enterprise Communication Server Release 9
Installation and Maintenance for Survivable Remote EPN

555-233-121

Issue 2

November 2000

SREPN Maintenance

2-31

Fault isolation procedures

2

Fiber direct-connect system

Figure 2-17

shows the loopbacks performed on the SNI and EI circuit packs.

Figure 2-17.

Fiber fault isolation tests for SNI and EI circuit packs

Figure 2-17

shows that:

■

Test #756 reports the result of the off-board loopback

■

Test #757 reports the result of the on-board loopback

■

Test #756 and Test #757 can run individually or as part of the test board
UUCSS long command for an SNI circuit pack.

■

Test #242 can be run as part of the test board UUCSS long command for
an Expansion Interface circuit pack. In addition to testing on-board
components, this test is helpful for isolating problems

between a circuit

pack and the lightwave transceiver

.

The loopback shown in this diagram shows only part what Test #242 does.
If no lightwave transceiver is connected to the Expansion Interface circuit
pack, an on-board loopback is performed on the Expansion Interface circuit
pack. For more information about Test #242, see the EXP-INTF
Maintenance Object in Chapter 9 of

DEFINITY ECS Release 9

Maintenance for R9r

.

cydf058 RPY 022499

TN753

switch

node

interface

TN570C

expansion

interface

Test #

757

Test #

756

Test #

242

Tone

clock

Tone

detector

DEFINITY

ECS

SREPN

TDM

BUS

Fiber optic

cable

Back of
cabinet

Back of
cabinet

Lightwave

transceivers

Test #989

(framing)

Test #989

(framing)

«
...
83
84
85
86
87
...
»

Содержание DEFINITY SERIES






































































































Отзывы:

Нет отзывов