manualshive.com logo in svg

Avaya DEFINITY SERIES, Руководство по установке и обслуживанию, Страница: 20 / 101

Поделиться
Скачать
Avaya DEFINITY SERIES Скачать руководство пользователя страница 20

DEFINITY Enterprise Communication Server Release 9
Installation and Maintenance for Survivable Remote EPN  

555-233-121  

Issue 2

November 2000

About This Document 

xx

Federal Communications Commission statement 

Means of connection

Connection of this equipment to the telephone network is shown in the following 
table.

If the terminal equipment (DEFINITY

®

 System) causes harm to the telephone 

network, the telephone company may notify you in advance that temporary 
discontinuance of service is be required. But if advance notice is not practical, the 
telephone company may notify the customer as soon as possible. Also, you will 
be advised of your right to file a complaint with the FCC if you believe it is 
necessary.

The telephone company may make changes in its facilities, equipment, 
operations, or procedures that could affect the operation of the equipment. If this 
happens, the telephone company will provide advance notice so you can make 
the necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment or for repair or warranty information, 
please contact the Technical Service Center at 1-800-248-1234. If the equipment 
causes harm to the telephone network, the telephone company may request that 
you disconnect the equipment until the problem is resolved.

It is recommended that repairs be performed by Avaya-certified technicians.

The equipment cannot be used on public coin phone service provided by the 
telephone company. Connection to party line service is subject to state tariffs. 
Contact the state public utility commission, public service commission, or 
corporation commission for information.

This equipment, if it uses a telephone receiver, is hearing aid compatible.

Manufacturer’s Port 

Identifier

FIC Code

SOC/REN/ 

A.S. Code

Network Jacks

Off/On Premises Station

OL13C

9.0F

RJ2GX, RJ21X, 
RJ11C

DID Trunk

02RV2-T

0.0B

RJ2GX, RJ21X

CO Trunk

02GS2

0.3A

RJ21X

CO Trunk

02LS2

0.3A

RJ21X

Tie Trunk

TL31M

9.0F

RJ2GX

1.544 Digital Interface

04DU9-B, C

6.0P

RJ48C, RJ48M

1.544 Digital Interface

04DU9-BN, KN

6.0P

RJ48C, RJ48M

120A2 Channel Service Unit

04DU9-DN

6.0P

RJ48C

Содержание DEFINITY SERIES






































































































Отзывы:

Нет отзывов