Avaya DEFINITY SERIES Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 101

Avaya DEFINITY SERIES Скачать руководство пользователя страница 52

DEFINITY Enterprise Communication Server Release 9
Installation and Maintenance for Survivable Remote EPN

555-233-121

Issue 2

November 2000

SREPN Installation

1-32

Test the SRP

1

3. Type status health and press

Enter

on the SRP system. The status of the

SREPN should be “down.” See

Figure 1-17

.

Figure 1-17.

Status health screen (SRP)

4. Place a voice call from a telephone on the Release 9r PPN to a telephone

on the SREPN and verify the talk path.

5. Physically disconnect all PNC A and B fiber cables from the connectors on

the rear of the SRP cabinet. Take care not to mix up or contaminate the
fibers. After about a minute, the red emergency transfer LED on TN775C
maintenance circuit pack turns on.

6. Verify that the red SURVIVE MODE ON LED on the TN2301 turns on in

approximately 2 minutes. The SREPN performs a cold reset and functions
again under the control of the SRP, although it may take longer for some
facilities (such as trunks) to be fully restored.

If the SURVIVE MODE ON LED does not turn on, refer to

‘‘Testing the

TN2301 function and wiring’’

Chapter 2, ‘‘SREPN Maintenance’’

.

7. Type status health and press

Enter

on the Release 9r system. The status

of the SREPN should be “dn” or “fe” (far end).

8. Type status health and press

Enter

on the SRP system. The status of the

SRP should be “up.”

9. Place a voice call between two telephones on the EPN and verify the talk

path.

10. Reconnect all PNC A and B fiber cables to the rear of the SRP cabinet.

11. Move the TN2301 switch to the restore (RSTR) position. The SURVIVE

MODE ON LED immediately turns off.

status health
ALARM SUMMARY     CABINET STATUS
Major: 1    Emerg Alarms
Minor: 0    Cab Trans Mj Mn Wn PNC
Warning: 10    1 auto- 0| 0| 5 up
BUSY-OUT SUMMARY    2 auto- 1| 0| 0 dn
Trunks: 0    3 n.a. 0| 0| 0 dn
Stations: 0
Others: 0
PROCESSOR OCCUPANCY STATUS
Static: 1% SM: 4%
CP: 0% Idle: 95%
CRITICAL SYSTEM STATUS
Active SPE: A/auto
Duplicated? SPE:n
SPE Power: commercial
Time Source: local
# Logins: 1

«
...
50
51
52
53
54
...
»

Содержание DEFINITY SERIES






































































































Отзывы:

Нет отзывов