manualshive.com logo in svg

Avaya DEFINITY SERIES, Руководство по установке и обслуживанию, Страница: 29 / 101

Поделиться
Скачать
Avaya DEFINITY SERIES Скачать руководство пользователя страница 29

DEFINITY Enterprise Communication Server Release 9
Installation and Maintenance for Survivable Remote EPN  

555-233-121  

Issue 2

November 2000

SREPN Installation 

1-9

Install the SRP cabinet 

1

Install ground plates

Ground plates are installed between stacked cabinets, provide the ground 
connection between cabinets, provide radio frequency (RF) radiation protection, 
and help stabilize the cabinets.

Install rear ground plates (Systems with
earthquake protection)

1. Loosen the four screws at the bottom of the top cabinet and at the top of 

the cabinet underneath the top cabinet. See 

Figure 1-2 on page 1-8

.

2. Align the mounting holes in the rear ground plate over the bottom screws in 

the top cabinet. See 

Figure 1-3 on page 1-10

.

3. Align the mounting holes in the ground plate with the four holes at the top 

of the cabinet below the top cabinet. Slide the mounting plate down to seat 
on the screws.

4. Do not tighten the screws yet.

Install front ground plates (Systems with
radiation shielding and earthquake protection)

Use the front ground plate instead of the cabinet clip to attach the cabinets to 
each other. Use one front ground plate between two 

stacked

 cabinets.

1. At the front of the cabinets, align the holes in the top of the front ground 

plate with the holes at the bottom of the upper cabinet, and insert the four 
screws. Do not tighten the screws yet. See 

Figure 1-3 on page 1-10

.

2. At the front of the cabinets, align the holes in the bottom of the front ground 

plate with the holes at the top of the lower cabinet. Insert the four supplied 
#12-24 x 1/2-inch (1.27 cm) thread-forming screws. 

3. Tighten all screws securely.

Содержание DEFINITY SERIES






































































































Отзывы:

Нет отзывов