Avaya DEFINITY SERIES Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 101

Avaya DEFINITY SERIES Скачать руководство пользователя страница 71

DEFINITY Enterprise Communication Server Release 9
Installation and Maintenance for Survivable Remote EPN

555-233-121

Issue 2

November 2000

SREPN Maintenance

2-17

Maintenance procedure

2

Health of Port Network Connections (PNC)

Depending on the conditions present when the system switched from Normal to
Survive mode, it may be in either Emergency Transfer or Survive mode.

To determine the mode in which the system is operating:

1. Get on overall report on each cabinet’s PNC status (status health)

on both

the Release 9r and the SRP systems

.

Figure 2-9

shows the Release 9r

screen, and

Figure 2-10

shows the SRP screen.

Figure 2-9.

Status health screen (Release 9r)

Figure 2-10.

Status health screen (SRP)

status health SPE A

PNC: A-PNC/auto B-PNC/functional   ALARMS: Maj:   2  Min:   2  Wrn: 104
Pwr: comm Sync:loc l Logins:2 BUSYOUT: Trk 0 Stn: 0 Oth: 18
Cab EmTr  Mj Mn Wn PNC     Cab EmTr Mj Mn Wn PNC      Cab EmTr  Mj Mn Wn PNC
1 auto- 0| 0|47 up
  2 auto- 0| 0|12 up

status health
ALARM SUMMARY     CABINET STATUS
Major: 1    Emerg Alarms
Minor: 0    Cab Trans Mj Mn Wn PNC
Warning: 10    1 auto- 0| 0| 5 up
BUSY-OUT SUMMARY    2 auto- 1| 0| 0 dn
Trunks: 0    3 n.a. 0| 0| 0 dn
Stations: 0
Others: 0
PROCESSOR OCCUPANCY STATUS
Static: 1% SM: 4%
CP: 0% Idle: 95%
CRITICAL SYSTEM STATUS
Active SPE: A/auto
Duplicated? SPE:n
SPE Power: commercial
Time Source: local
# Logins: 1

«
...
69
70
71
72
73
...
»

Содержание DEFINITY SERIES






































































































Отзывы:

Нет отзывов